Lighting Systems — An Introduction to ANSI C137.1

February 6, 2017

Roy Harvey

The recently formed ANSI C137 Lighting Systems Committee created a working group to develop a standard for a zero-to-10 volt analog interface between dimmable LED drivers, fluorescent ballasts and dimming controls. At present, there is no widely accepted industry standard for analog dimming of LED sources. The new standard, C137.1, will enhance interoperability of drivers and dimming controls and improve the uniformity of output of multiple drivers operating on the same control circuit.

Photo credit: Osram Sylvania

The standard is based on the 0-10 V fluorescent dimming interface specified in ANSI C82.11 Annex A, which is similar to the interface specified in IEC 60929 Annex E. C137.1 adds several new features and specifies the interface in more detail.

The main new feature is a standby or “electronic off” mode. This optional mode disables the driver’s output power while its control circuitry remains awake. This feature can eliminate a relay used to disconnect the driver’s output and an extra pair of wires to control the relay. Standby mode is entered when the control signal drops below about 0.5 V. C137.1 also adds specifications for dynamic response, the time to start up or change from one level to another.

However, the standard covers more than drivers and ballasts; it also has requirements for dimming controls and system wiring. Like C82.11, C137.1 specifies that the driver or ballast supply current that the control unit sinks and uses to generate the control voltage. C137.1 requires that the control unit manufacturer declare how much current the control unit can sink. This gives a lighting system designer information needed to help ensure that the control unit can handle the current sourced by the driver(s) connected to it. C137.1 also specifies that multiple controls, such as a wall dimmer and a daylight sensor, can connect to the same control wires without damaging each other.

Finally, C137.1 requires that the voltage drop caused by control wiring resistance be no more than 0.3 V. This helps ensure adequate noise margin and uniform operation (light levels) of many drivers sharing control wires. Requirements on tolerances for the endpoints of the dimming range further contribute to uniform operation.

The working group has been developing the standard since February 2015. A draft is being prepared for public review according to the ANSI process. The standard is expected to be published in early 2017, but some of the above information may change, so it is best to check the published edition.

If you have questions regarding these new regulatory requirements or need immediate testing to ensure that your products are in compliance, please contact UL to discuss testing, advisory or training needs at PerformanceLighting@ul.com.


Roy Harvey is SSL Electronics & Infrastructure Standards Manager at Osram Sylvania. He is also Vice-chair of ASC C137 and Head of C137.1 Ad Hoc Group.

 

Related Articles


Changing Scene

  • LEDVANCE Expands Ontario Presence with New Specification Agent

    LEDVANCE Expands Ontario Presence with New Specification Agent

    LEDVANCE is pleased to announce the appointment of Sterling Architectural Products Ltd. (Sterling Lights) as their new specification agent in Ontario. This partnership strengthens LEDVANCE’s presence in the region and reinforces their commitment to serving the professional lighting design and specification community with innovative, reliable lighting solutions. With decades of experience and a service-driven mindset,… Read More…

  • May 29, 2025 - Eureka Wins Three 2025 Red Dot Awards for Product Design

    Eureka Wins Three 2025 Red Dot Awards for Product Design

    Eureka is pleased to announce that its Velia, Cirra, and Junction luminaires have each received a 2025 Red Dot Design Award for Product Design. It is the 11th consecutive year that Eureka products have been honored with this prestigious award, which is a testament to the company’s consistency and relentless drive to design exceptional luminaires.… Read More…


Design

  • Mac’s II Agencies: Case Study – Tesoro, Vancouver, BC

    Mac’s II Agencies: Case Study – Tesoro, Vancouver, BC

    At the crest of False Creek, Tesoro stands as a contemporary interpretation of classic luxury, offering 92 exclusive waterfront homes in the heart of Vancouver. Developed by Concert Properties, this 17-story residential tower embraces a distinctly modern character, harmonizing sleek design with timeless sophistication. The vision for Tesoro extended beyond its architectural presence—it was about… Read More…

  • LightForm: Estiluz – Versatile Solutions for Sophisticated Spaces

    LightForm: Estiluz – Versatile Solutions for Sophisticated Spaces

    For anyone seeking high-performance lighting that blends elegance with engineering, Estiluz offers an exceptional range of solutions. This Spanish brand, family-owned since 1969, creates lighting that balances form, function, and flexibility, making it ideal for both bold architectural statements and subtle design enhancements. At LightForm, they are proud to be the exclusive Canadian distributor of… Read More…


New Products

  • Cyclone Lighting Introduces New Taji Luminaire

    Cyclone Lighting Introduces New Taji Luminaire

    Cyclone Lighting is excited to announce the release of its new Taji luminaire. Taji’s captivating design features high-performance optics and enhances a variety of aesthetics. Taji’s distinctive, stylish silhouette and slender lines are a refreshing departure from the ubiquitous dome luminaire. The unique flared form maintains a slender, minimalist feel yet provides high-performance optics. The… Read More…

  • Leviton Releases New Decora Smart Wi-Fi 0-10V Dimmer for Home & Small Business Lighting Control

    Leviton Releases New Decora Smart Wi-Fi 0-10V Dimmer for Home & Small Business Lighting Control

    Leviton has announced the launch of the Decora Smart Wi-Fi 0-10V Dimmer (D2710), expanding its comprehensive Wi-Fi lighting and load control solutions that work with the My Leviton app. As the first Matter-compatible 0-10V smart dimmer, the new 120V/277V device makes it easy to add 0-10V dimming to smart platforms such as Apple Home, Amazon… Read More…